Re: d8b runs for good until I turn on automation or final mi
Posted: Mon Oct 13, 2014 1:54 pm
Here is what the voltages should look like if you get a hold of a meter.
Here is what the voltages should look like if you get a hold of a meter.
d8b Forum
The new alternative forum for d8b users
http://www.d8bforum.com/phpBB3/
d8b runs for good until I turn on automation or final mix
Page 2 of 3
Posted: Mon Oct 13, 2014 1:54 pmHere is what the voltages should look like if you get a hold of a meter.
Re: d8b runs for good until I turn on automation or final mi
Posted: Mon Oct 13, 2014 4:26 pmthanks Crash I will see if I can find someone with a meter and get
them to check it for me. hope I can find someone.
its true just when you think your out of the water jaws gets you every time
thanks Joe Allen
them to check it for me. hope I can find someone.
its true just when you think your out of the water jaws gets you every time
thanks Joe Allen
Re: d8b runs for good until I turn on automation or final mi
Posted: Mon Oct 13, 2014 6:02 pmDon't know if you saw Vert360's post but he is experiencing something very similar to your situation.
Re: d8b runs for good until I turn on automation or final mi
Posted: Mon Oct 13, 2014 8:04 pmthanks again Crash
this is a hard one to work out just hope I can
your a good man Crash
Joe Allen
this is a hard one to work out just hope I can
your a good man Crash
Joe Allen
Re: d8b runs for good until I turn on automation or final mi
Posted: Mon Oct 13, 2014 10:42 pmYa it looks like it might be the same, just wanted to know if garrett21allen D8B still passes audio, and everything is still being clocked. Just the only thing that doesnt work is both the MFX and UFX cards?
Re: d8b runs for good until I turn on automation or final mi
Posted: Mon Oct 13, 2014 10:45 pmDo you think a fuse might have been blown?
Re: d8b runs for good until I turn on automation or final mi
Posted: Tue Oct 14, 2014 12:02 amThere three fuses inside the cpu/power supply that are easy enough to check. Let us know what you find.
Re: d8b runs for good until I turn on automation or final mi
Posted: Tue Oct 14, 2014 2:09 pmHi Vert360
yes everything works when the lights go out but only from the monitor
even the MFX-UFX cards work from what I can tell. I don't know if its the fuse or not
on mine it looks like if it was a bad fuse then I don't think the lights would come on at all
but I could be wrong. let me know if you find anything on your end. and I will do the same
thanks for any help on this.
Joe Allen
yes everything works when the lights go out but only from the monitor
even the MFX-UFX cards work from what I can tell. I don't know if its the fuse or not
on mine it looks like if it was a bad fuse then I don't think the lights would come on at all
but I could be wrong. let me know if you find anything on your end. and I will do the same
thanks for any help on this.
Joe Allen
Re: d8b runs for good until I turn on automation or final mi
Posted: Tue Oct 14, 2014 4:24 pmWell it looks like everything is working for me. I just reseated every ribbon cable, dont know how long it will last. I have had the board on and off for about 5 hours. I think it might have something to with heat, I noticed now that it is colder in houston, (I dont leave the AC on when i leave the Studio, and it gets hot in here) that it has been acting right. The weird thing is, if I raise the fader all the way to 10db via the GUI side, It gets stuck and will not slide down, when i try to move it with the motorize fader. But if i move the fader manually via the motorize fader it doesnt get stuck, the only way i can get it back to moving is using the fader calibration.
Re: d8b runs for good until I turn on automation or final mi
Posted: Wed Oct 15, 2014 4:18 pmGarrett21allen have you tried to resit all the the cables?